1448
College of Engineering, Architecture and Technology
3. Earn a grade of “C” or better in technical courses required for the degree and taken prior to admission to professional school. In these courses, meet or exceed the Technical GPA requirement listed in the Departmental GPA Requirements section below (when applicable). Note: Technical courses include astronomy, biology, biochemistry, chemistry, geology, engineering (BAE, CHE, CIVE, IEM, ECEN, ENGR, ENSC, MAE), math, physics, statistics, zoology, and any additional science courses listed on the degree requirement sheet. 4. Complete a minimum of 12 credit hours of courses at OSU Stillwater or Tulsa, required for the degree. In these courses, meet or exceed the OSU GPA requirement listed in the Departmental GPA Requirements section below (when applicable). 5. Complete a minimum of 9 credit hours of technical courses at OSU Stillwater or Tulsa, required for the degree. In these courses, meet or exceed the OSU Technical GPA (all technical courses required for the degree taken at OSU) listed in the Departmental GPA Requirements section below (when applicable). 6. Earn a final grade of “C” or better in all courses submitted to satisfy the University’s English requirement. 7. Meet any additional requirements for the selected major, as specified below. 8. Demonstrate an acceptable level of academic competence in subject material comparable to that covered in pre-professional school as defined by the selected professional school below. Such demonstration may be by completion of coursework or by examination with not more than half the requirements satisfied by examination. 9. Demonstrate an acceptable level of professional potential, including academic integrity and ethical behavior, as determined by the department head. Departmental GPA Requirements All specified GPAs are calculated based on the last grade earned in repeated courses. The minimum GPA requirements by school, and any additional requirements, are as follows: 1. School of Biosystems and Agricultural Engineering: GPA Requirements for Professional School: Technical GPA-2.70, OSU GPA-2.70, OSU Technical GPA-2.70 and a grade of “C” or better in each course that is a prerequisite for a major course. 2. School of Chemical Engineering: GPA Requirements for Professional School: Technical GPA-2.70, OSU GPA-2.50, OSU Technical GPA-2.70. A final grade of “C” or better must be achieved in the required pre-professional courses (noted on the degree requirement sheet). If a “C” is obtained in ENGL 1113 Composition I or ENGL 1313 Critical Analysis and Writing I, ENGL 1213 Composition II or ENGL 1413 Critical Analysis and Writing II is also required. 3. School of Civil and Environmental Engineering: GPA Requirements for Professional School: Technical GPA-2.70, OSU GPA-2.50, OSU Technical GPA-2.70, and a grade of “C” or better in each course that is a prerequisite for a CIVE course and in all required technical pre-professional courses (noted on the degree requirement sheet) whether taken prior to professional school or not. Students may enroll in no more than nine hours of professional school major requirements prior to admission to professional school unless they secure permission from the head of the school. However, enrollment preference in such courses will be given to students admitted to the professional school. 4. School of Electrical and Computer Engineering:
GPA Requirements for Professional School: Technical GPA-2.70, OSU GPA-2.60, OSU Technical GPA-2.70. 5. School of Industrial Engineering and Management: GPA Requirements for Professional School: Technical GPA-2.50, and a grade of “C” or better in each course that is a prerequisite for an IEM course and in all technical pre-professional courses (noted on the degree requirement sheet) whether taken prior to professional school or not. 6. School of Mechanical and Aerospace Engineering: GPA Admission Requirements for Professional School: Technical GPA 3.0, OSU GPA 3.0, OSU Technical GPA-3.0. Admission and degree requirements: a grade of "C" or better in each course that is a prerequisite for an MAE course and in all technical pre-professional courses (noted on the degree requirement sheet) whether taken prior to professional school or not. Minimum GPA requirements for graduation: Overall GPA 2.50 GPA for MAE prefix courses-2.5 GPA for MAE 4000 level courses-2.5. Students may enroll in no more than nine hours of upper-division major requirements prior to admission to professional school unless they secure permission from the head of the school. However, enrollment preference in such courses will be given to students admitted to the professional school. 7. Refer to the School of Architecture catalog page (p. 1534) for requirements. 8. Refer to the relevant academic area on the Division of Engineering Technology catalog page (p. 1485) for requirements. Academic Areas • Biosystems and Agricultural Engineering (p. 1450) • CEAT Dean's Office and CEAT Online Learning (p. 1462) • Chemical Engineering (p. 1464) • Civil and Environmental Engineering (p. 1473) • Construction Engineering Technology (p. 1479) • Division of Engineering Technology (p. 1485) • Electrical and Computer Engineering (p. 1488) • Electrical Engineering Technology (p. 1496) • Engineering and Technology Management (p. 1502) • Fire Emergency Management Program (p. 1503) • Fire Protection and Safety Engineering Technology (p. 1506) • Industrial Engineering and Management (p. 1514) • Materials Science and Engineering (p. 1518)
• Mechanical and Aerospace Engineering (p. 1519) • Mechanical Engineering Technology (p. 1530) • School of Architecture (p. 1534)
Undergraduate Programs • Aerospace Engineering, BSAE (p. 1522) • Architectural Engineering: Construction Project Management, BEN (p. 1539) • Architectural Engineering: Mechanical, Electrical and Plumbing, BEN (p. 1541) • Architecture Engineering: Structures, BEN (p. 1545) • Architecture, BAR (p. 1547) • Biosystems Engineering (General Option), BSBE (p. 1452) • Biosystems Engineering: Bioprocessing & Food Processing, BSBE (p. 1454)
Powered by FlippingBook